Tiers: may be specified as single-tier (full height), two-tier, three-tier, etc., meaning that the lockers are stacked on top of each other in layers two high, three high, etc. Tiers are commonly up to eight high; on occasion, even more tiers may be found, in the case of very small lockers for such purposes as storing laptop computers. The most common numbers of tiers found in lockers are, in order, one, two, and four; three-tier lockers are rather less common, and other numbers such as five, six, or eight even less common still - seven almost non-existent. Since locker cabinets are most commonly 6 feet (182.9 cm.) high (although there are exceptions), the height of individual lockers varies according to how many tiers are accommodated within the cabinet. The height of individual lockers is usually approximately 6 feet (182.9 cm.) divided by the number of tiers, so that two-tier lockers are about 3 feet (91.4 cm.) high, three-tier lockers 2 feet (61 cm.) high, four-tier lockers 1.5 feet (45.7 cm.) high, and so on. Standard features often vary according to the number of tiers: single-tier lockers usually include a shelf about a foot (roughly 30 cm.) from the top, and a hanging rail (sometimes with one or two hooks) immediately underneath that, at the top of the large compartment beneath the shelf; two- or three-tier lockers usually lack the shelf, but include the hanging rail; lockers with four or more tiers usually have none of these fittings, but consist of just the bare compartment.
Buy Denver Lockers
Unassembled metal lockers typically ship within 24 to 48 hours and are a great option when lockers are needed on site quickly. We also offer professional, expert and timely assembly of lockers. Metal lockers are used for a variety of applications such as employee lockers, school lockers, student lockers, restaurant lockers, day care lockers, pool lockers, gym lockers, club lockers, fire department lockers, police lockers, apartment lockers and home lockers.
Lockers are usually physically joined together side by side in banks, and are commonly made from steel, although wood, laminate, and plastic are other materials sometimes found. Steel lockers which are banked together share side walls, and are constructed by starting with a complete locker; further lockers may then be adding by constructing the floor, roof, rear wall, door, and just one extra side wall, the existing side wall of the previous locker serving as the other side wall of the new one. The walls, floors, and roof of lockers may be either riveted together (the more traditional method) or, more recently, welded together.
The Operator (including employees, agents, and/or contractors of the Operator, the event and the venue) and/or law enforcement officials may inspect any and all items before they are stored in a locker or the facility and may, in their sole discretion, refuse to permit storage any items that may cause a risk and/or nuisance to the Operator, other users, the storage facility, the venue or the event.
Stepped/2-step lockers are two-tier lockers, usually available only in 15-inch (38-cm.) width; but the compartments and their doors have an L-shaped cross-section, which causes the division between the doors to follow a zigzag pattern. This configuration enables more hanging height to be included in both upper and lower lockers; but part of each compartment (the lower part of the upper one and the upper part of the lower one) will be only half the usual width of two-tier lockers.
Clean/dirty lockers normally have two or three parts within the locker. One part is meant for dirty or clothes that are worn, and the other side for clean clothes. These lockers are meant for hospitals or other medical workplaces where it is useful to keep work and personal clothes apart to reduce the risk of infection. These lockers are also useful for factories where work clothes can become dirty and it can be very useful to keep them apart from personal clothes.
Locking options: various types of key locking or padlocking facility are available now. Key locking options include flush locks, cam locks, or locks incorporated into a rotating handle; padlocking facilities may be a simple hasp and staple, or else a padlocking hole may be included in a handle, often called a latchlock. More modern designs include keyless operation, either by coin deposit (which may or may not be returned when use of the locker terminates), or by using electronic keypads to enter passwords for later reopening the locker. Some older lockers used a drop-latch which was incorporated into the door handle, and slid up and down and could be padlocked at the bottom in the "down" position, but these are less used now. Three-point locking is not possible with this type of latch, because it needs to be operated by means of a latch that rotates rather than slides up and down; so this drop-latch is probably a less secure locking option, which may be why it is little used nowadays. Prefect Combination locks are very popular in school lockers used in the UK due to their ease of use and the time and cost saved in the removal of locker keys.
Southwest Solutions Group® provides design and installation services for computerized grocery pickup refrigerated and freezer lockers for residential applications, restaurants, student housing, universities, and more in Denver, Colorado Springs, Aurora, Fort Collins, Boulder, and Pueblo. We will also provide you with a free consultation to determine your exact needs and specifications before the design process begins. To learn more or to speak with a specialist, call us at (303) 741-1600 or send us a message today.
The visually appealing and very durable Traditional Collection is our most widely distributed locker line. Offering the most value for typical locker applications, this collection is available in a full range of spacious sizes, from single- to six-tier configurations, as well as two-person, 16-person and wall-mounted. The addition of our new 2 person Z-Locker completes the Traditional collection. Denver Lockers Click Here