Gun lockers or safes are specifically designed for the secure storage of guns and ammunition. They broadly resemble normal single-tier lockers, but tend to be slightly less high than normal single-tier lockers, and are often free-standing, and not banked together. They are fitted with internal racks designed for holding firearms. They have a shelf at the top like normal single-tier lockers, although in this case it is closed and locked by a separate door, because of legal requirements in some countries that firearms and ammunition be stored and locked separately. They always lock with three-point locking, which is in some countries a legal requirement for the storage of firearms. Sometimes they are made of the standard kind of sheet steel used in manufacturing normal lockers, and sometimes they are made of extremely thick heavy-duty steel and in this case resemble a safe more than a normal locker. In Australia there are strict regulations governing the storage of firearms following the Port Arthur massacre in Tasmania, Australia on 28 April 1996, and cabinets used for storing firearms must be bolted to the floor or a wall if the cabinet is under a certain weight. Dedicated gun lockers are likely to include holes in the cabinet to accommodate such bolting. Several locker manufacturers also offer dedicated gun lockers.
Lockers are usually physically joined together side by side in banks, and are commonly made from steel, although wood, laminate, and plastic are other materials sometimes found. Steel lockers which are banked together share side walls, and are constructed by starting with a complete locker; further lockers may then be adding by constructing the floor, roof, rear wall, door, and just one extra side wall, the existing side wall of the previous locker serving as the other side wall of the new one. The walls, floors, and roof of lockers may be either riveted together (the more traditional method) or, more recently, welded together.
Stepped/2-step lockers are two-tier lockers, usually available only in 15-inch (38-cm.) width; but the compartments and their doors have an L-shaped cross-section, which causes the division between the doors to follow a zigzag pattern. This configuration enables more hanging height to be included in both upper and lower lockers; but part of each compartment (the lower part of the upper one and the upper part of the lower one) will be only half the usual width of two-tier lockers.
The rental of the lockers and these Terms & Conditions are governed under and by the laws of the State of Washington. The parties consent and agree that the exclusive jurisdiction and venue for any dispute or claim relating to the rental and/or use of the lockers and/or locker facility, whether in contract, tort, or any other area of the law, shall be in Seattle, Washington.
With the same standard features as the Traditional line, the Traditional Plus Collection is intended for more rugged applications and has matching finish on all sides and top for a finished look. Phenolic Lockers are the material of choice when a high degree of design flexibility is desired or where durability and strength are required. These lockers are fabricated to stand the test of time. The dense components, combined with stainless steel brackets and fasteners, stand up to the most extreme conditions of moisture and humidity. Phenolic is impact, water and corrosion resistant, and does not support bacteria.
Number of locking points: Locker doors may lock with either single- or three-point locking, but this is not normally chosen as a separate option, and the choice is usually dependent on the number of tiers in the lockers, or whether they are a high-security model, although some manufacturers do allow purchasers to specifically choose an option here that goes against their normal practice. Single-point locking locks the door at only the point where the latch engages with the door-frame, whereas three-point locking uses extensible steel rods to lock the top and bottom of the door as well.
Teaming up with the Saint Francis Center, Denver is also planning on adding 200 more storage spaces at the organization’s employment service center, located near the city’s capital building. The contract between the city of Denver and the Saint Francis Center will start on June 1 and with $130,000 for the first year of storage space. After that, the center will be given $100,000 a year if the contract continues.
THE OPERATOR (INCLUDING EMPLOYEES, AGENTS, AND/OR CONTRACTORS OF THE OPERATOR, THE EVENT AND THE VENUE) SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL LOSSES ARISING FROM THE LOSS OF OR INABILITY TO ACCESS ITEMS STORED WITHIN THE LOCKERS AND LOCKER FACILITY, INCLUDING BUT NOT LIMITED TO, MISSED AIRLINE FLIGHTS OR OTHER TRANSPORTATION OR LOSS OF BUSINESS AND SHALL NOT BE LIABLE FOR LOSS OF PROPERTY DUE TO CUSTOMER’S LOSS OF LOCKER KEYS OR COMBINATIONS.
Officeworks School List Service is backed by our Parents Price Promise - ‘Find an identical stocked item on a quoted school list at a lower price and we’ll beat it by 20%’. For 2019 school lists, the Parents Price Promise is only applicable on prices that appear on valid 2018 school book lists for the quantity listed. Valid on identical stocked or Officeworks-deemed equivalent items where identical products are not available. Excludes competitor out of stocks, categories or items not ranged and items available only for customer order at Officeworks. Offer available from 01/09/18 to 11/02/19. Cannot be used in conjunction with Officeworks’ 5% Price Guarantee.
Damn right we blame Trump for the shutdown, afterall he did brag about owning the shutdown. Trump will also own shutdown 2.0 that will start 2-16 after he rejects every bill Democrats put forward. Shutdown 2.0 will be used by our lying, cheating president as cover as he desperately tries to change the subject away from the Mueller investigation and pick another fight rather than govern.
At Shelving Rack & Lockers, Inc. we are always doing our part to recycle good industrial storage equipment. We are continually looking for quality used products that are in usable and sturdy condition. Doing so allows us to give you great products as well as incredible savings. Additionally, it helps us do our part to keep unnecessary items out of our landfills, making our environment more green.
3-Tier Locker compartments measure 19 in. high and 3-Tier Locker compartments measure 19 in. high and include two side hooks and number plates. Doors have top and bottom louvers for air ventilation. Recessed handle with finger-lift latch accommodates a standard padlock (not included). Welded steel construction with powder coat finish available in 17 colors. Overall size of locker ... More + Product Details Close