Lockers are usually physically joined together side by side in banks, and are commonly made from steel, although wood, laminate, and plastic are other materials sometimes found. Steel lockers which are banked together share side walls, and are constructed by starting with a complete locker; further lockers may then be adding by constructing the floor, roof, rear wall, door, and just one extra side wall, the existing side wall of the previous locker serving as the other side wall of the new one. The walls, floors, and roof of lockers may be either riveted together (the more traditional method) or, more recently, welded together.
Please take our policies seriously. Anyone who violates our policies might be asked to leave. Persons involved in serious incidents or repeat offenders will be subjected to sanctions under the Student Code of Conduct. Non-student offenders or repeat offenders will be subject to sanctions by the Facility Manager or by the Director of Recreational Sports. Sanctions may include, but are not limited to, suspension from facilities, revoking of membership privileges, student disciplinary sanctions or civil prosecution.
There are a number of features or characteristics which may vary in lockers. Because purchasers will need to specify what they want in each of these when ordering, it is more common to order a particular configuration rather than buy "off the shelf" in a shop, although certain very common configurations can be found in shops fairly easily. These features include:
Wilderness Exchange is within walking distance of Union and they require you leave a bag with them when you go into the store, they may be willing to stash your bag for a few hours. No guarantee on that, but an option if you can't find anything else. They are only open 10am-6pm on Sundays, so you may have to wait around a bit or pick it up early depending on when you get there and will be leaving.
The rental of the lockers and these Terms & Conditions are governed under and by the laws of the State of Washington. The parties consent and agree that the exclusive jurisdiction and venue for any dispute or claim relating to the rental and/or use of the lockers and/or locker facility, whether in contract, tort, or any other area of the law, shall be in Seattle, Washington.
With the same standard features as the Traditional line, the Traditional Plus Collection is intended for more rugged applications and has matching finish on all sides and top for a finished look. Phenolic Lockers are the material of choice when a high degree of design flexibility is desired or where durability and strength are required. These lockers are fabricated to stand the test of time. The dense components, combined with stainless steel brackets and fasteners, stand up to the most extreme conditions of moisture and humidity. Phenolic is impact, water and corrosion resistant, and does not support bacteria.
Number of locking points: Locker doors may lock with either single- or three-point locking, but this is not normally chosen as a separate option, and the choice is usually dependent on the number of tiers in the lockers, or whether they are a high-security model, although some manufacturers do allow purchasers to specifically choose an option here that goes against their normal practice. Single-point locking locks the door at only the point where the latch engages with the door-frame, whereas three-point locking uses extensible steel rods to lock the top and bottom of the door as well.
Sloping tops: while most lockers have flat tops, some manufacturers offer the option of sloping tops to their range of lockers. The slope may be of either 30 degrees or 45 degrees to the horizontal, sloping towards the front, and the purpose of this is to make it impossible to store items on top of the lockers, or to make it harder for dust or other debris to accumulate there. This is an important factor in places like food-processing factories or restaurants where hygiene requirements must be met.
Examine the scepter to obtain the Red Jewel. This goes into the Bejeweled Box, which you can get in the Interrogation Room. Accessing this area requires the Club Key, so if you don't have that yet, keep progressing the story until you get it. Once you've got the Bejeweled Box, combine it with the Red Jewel to get the S.T.A.R.S. badge. You can use this item in two locations: the Underground Stairs in the Middle section of the Underground Facility, and the S.T.A.R.S. Office.
Division 10 — Specialties Lockers: Division 10 — Specialties is a category within the National Master Specification (NMS) set of guidelines developed by Public Works and Government Services Canada. Division 10 — Specialties items that could be required within a locker room (to meet commercial building and construction regulations) are lockers, washroom accessories, toilet compartments, and toilet partitions. Lockers are constructed of two sides: a back, top and a bottom. Different types of materials are used in locker manufacturing, offering a wide variety of metal lockers, stainless steel lockers, solid plastic lockers, solid phenolic lockers, and custom lockers. A padlock is the most common way to lock a locker; however, you can also use a keyed cylinder lock, built in combination locks or keypad locks. There are a lot of optional extras that can be utilized for lockers, for example: bases, sloping tops, end panels, customized shelves and hooks as well as the locking method (coin-operated lockers are another option). The environment is the best way to distinguish what type of locker will be required for which type of space. For example, if you are putting gym lockers into a humid area, or anywhere close to showers, stainless steel or solid plastic lockers would be most suitable because they are moisture-resistant and rust-resistant. Wood lockers would not be appropriate for this type of environment because the moisture from the humidity would rot the wood.